makes it easier to run on bsd's, where you cannot (easily?) let non-root users
bind to ports <1024. starting as root also paves the way for future improvements
with privilege separation.
unfortunately, this requires changes to how you start mox. though mox will help
by automatically fix up dir/file permissions/ownership.
if you start mox from the systemd unit file, you should update it so it starts
as root and adds a few additional capabilities:
# first update the mox binary, then, as root:
./mox config printservice >mox.service
systemctl daemon-reload
systemctl restart mox
journalctl -f -u mox &
# you should see mox start up, with messages about fixing permissions on dirs/files.
if you used the recommended config/ and data/ directory, in a directory just for
mox, and with the mox user called "mox", this should be enough.
if you don't want mox to modify dir/file permissions, set "NoFixPermissions:
true" in mox.conf.
if you named the mox user something else than mox, e.g. "_mox", add "User: _mox"
to mox.conf.
if you created a shared service user as originally suggested, you may want to
get rid of that as it is no longer useful and may get in the way. e.g. if you
had /home/service/mox with a "service" user, that service user can no longer
access any files: only mox and root can.
this also adds scripts for building mox docker images for alpine-supported
platforms.
the "restart" subcommand has been removed. it wasn't all that useful and got in
the way.
and another change: when adding a domain while mtasts isn't enabled, don't add
the per-domain mtasts config, as it would cause failure to add the domain.
based on report from setting up mox on openbsd from mteege.
and based on issue #3. thanks for the feedback!
so you can run mox on openbsd with port redirects in pf.conf.
in the future, starting as root, binding the sockets, and passing the bound
sockets to a new unprivileged process should be implemented, but this should
get openbsd users going.
from discussion with mteege
so users can easily take their email out of somewhere else, and import it into mox.
this goes a little way to give feedback as the import progresses: upload
progress is shown (surprisingly, browsers aren't doing this...), imported
mailboxes/messages are counted (batched) and import issues/warnings are
displayed, all sent over an SSE connection. an import token is stored in
sessionstorage. if you reload the page (e.g. after a connection error), the
browser will reconnect to the running import and show its progress again. and
you can just abort the import before it is finished and committed, and nothing
will have changed.
this also imports flags/keywords from mbox files.
ideally both account & admin web pages should be on non-public ips (e.g. a
wireguard tunnel). but during setup, users may not have that set up, and they
may want to configure the admin/account pages on their public ip's. the auth
rate limiting should make it less of issue.
users can now also only put the account web page publicly available. useful for
if you're the admin and you have a vpn connection, but your other/external
users do not have a vpn into your mail server. to make the account page more
easily findable, the http root serves the account page. the admin page is still
at /admin/, to prevent clash with potential account pages, but if no account
page is present, you are helpfully redirected from / to /admin/.
this also adds a prometheus metric counting how often auth attempts have been
rate limited.
before, we used heuristics to decide when to train/untrain a message as junk or
nonjunk: the message had to be seen, be in certain mailboxes. then if a message
was marked as junk, it was junk. and otherwise it was nonjunk. this wasn't good
enough: you may want to keep some messages around as neither junk or nonjunk.
and that wasn't possible.
ideally, we would just look at the imap $Junk and $NotJunk flags. the problem
is that mail clients don't set these flags, or don't make it easy. thunderbird
can set the flags based on its own bayesian filter. it has a shortcut for
marking Junk and moving it to the junk folder (good), but the counterpart of
notjunk only marks a message as notjunk without showing in the UI that it was
marked as notjunk. there is also no "move and mark as notjunk" mechanism. e.g.
"archive" does not mark a message as notjunk. ios mail and mutt don't appear to
have any way to see or change the $Junk and $NotJunk flags.
what email clients do have is the ability to move messages to other
mailboxes/folders. so mox now has a mechanism that allows you to configure
mailboxes that automatically set $Junk or $NotJunk (or clear both) when a
message is moved/copied/delivered to that folder. e.g. a mailbox called junk or
spam or rejects marks its messags as junk. inbox, postmaster, dmarc, tlsrpt,
neutral* mark their messages as neither junk or notjunk. other folders mark
their messages as notjunk. e.g. list/*, archive. this functionality is
optional, but enabled with the quickstart and for new accounts.
also, mox now keeps track of the previous training of a message and will only
untrain/train if needed. before, there probably have been duplicate or missing
(un)trainings.
this also includes a new subcommand "retrain" to recreate the junkfilter for an
account. you should run it after updating to this version. and you should
probably also modify your account config to include the AutomaticJunkFlags.
for example, by matching incoming messags on smtp mail from, verified domains
(spf/dkim), headers. then delivering to a configured mailbox. for mailing
lists, if a verified domain matches, regular spam checks can be skipped.
this was already possible by editing the configuration file, but only admins
can edit that file. now users can manage their own rulesets.
and change thunderbird autoconfiguration to use it.
unfortunately, for microsoft autodiscover, there appears to be no way to
request secure password negotiation. so it will default to plain text auth.
cram-md5 is less secure than scram-sha-*, but thunderbird does not yet support
scram auth. it currently chooses "plain", sending the literal password over the
connection (which is TLS-protected, but we don't want to receive clear text
passwords). in short, cram-md5 is better than nothing...
for cram-md5 to work, a new set of derived credentials need to be stored in the
database. so you need to save your password again to make it work. this was
also the case with the scram-sha-1 addition, but i forgot to mention it then.
- and don't have a global variable "d" in the big checkDomain function in http/admin.go.
- and set loglevel from command-line flag again after loading the config file, for all subcommands except "serve".
