when broadcasting a change, we would try to send the changes on a channel,
non-blocking. if we couldn't send (because there was no pending blocked
receive), we would wait until the potential receiver would explicitly request
the changes. however, the imap idle handler would not explicitly request the
changes, but do a receive on the changes channel. since there was no pending
blocked send on the channel, that receive would block. only when another event
would come in, would both the pending and the new changes be sent.
we now use a channel only for signaling there are pending changes. the channel
is buffered, so when broadcasting we can just set the signal by a non-blocking
send and continue with the next listener. the receiver will get the buffered
signal. it can then get the changes directly, but lock-protected.
found when looking at a missing/delayed new message notification in thunderbird
when two messages arrive immediately after each other. this doesn't fix that
problem though: it seems thunderbird just ignores imap untagged "exists"
messages (indicating a new message arrived) during the "uid fetch" command that
it issued after notifications from an "idle" command.
this doesn't really test the output of the ctl commands, just that they succeed
without error. better than nothing...
testing found two small bugs, that are not an issue in practice:
1. we were ack'ing streamed data from the other side of the ctl connection
before having read it. when there is no buffer space on the connection (always
the case for net.Pipe) that would cause a deadlock. only actually happened
during the new tests.
2. the generated dkim keys are relatively to the directory of the dynamic
config file. mox looked it up relative to the directory of the _static_ config
file at startup. this directory is typicaly the same. users would have noticed
if they had triggered this.
so mox doesn't have to be running when you run it.
will be useful for testing in the near future.
this also moves cpuprof and memprof cli flags to top-level flag parsing, so all
commands can use them.
the mailbox select/examine responses now return all flags used in a mailbox in
the FLAGS response. and indicate in the PERMANENTFLAGS response that clients
can set new keywords. we store these values on the new Message.Keywords field.
system/well-known flags are still in Message.Flags, so we're recognizing those
and handling them separately.
the imap store command handles the new flags. as does the append command, and
the search command.
we store keywords in a mailbox when a message in that mailbox gets the keyword.
we don't automatically remove the keywords from a mailbox. there is currently
no way at all to remove a keyword from a mailbox.
the import commands now handle non-system/well-known keywords too, when
importing from mbox/maildir.
jmap requires keyword support, so best to get it out of the way now.
so users can easily take their email out of somewhere else, and import it into mox.
this goes a little way to give feedback as the import progresses: upload
progress is shown (surprisingly, browsers aren't doing this...), imported
mailboxes/messages are counted (batched) and import issues/warnings are
displayed, all sent over an SSE connection. an import token is stored in
sessionstorage. if you reload the page (e.g. after a connection error), the
browser will reconnect to the running import and show its progress again. and
you can just abort the import before it is finished and committed, and nothing
will have changed.
this also imports flags/keywords from mbox files.
before, we used heuristics to decide when to train/untrain a message as junk or
nonjunk: the message had to be seen, be in certain mailboxes. then if a message
was marked as junk, it was junk. and otherwise it was nonjunk. this wasn't good
enough: you may want to keep some messages around as neither junk or nonjunk.
and that wasn't possible.
ideally, we would just look at the imap $Junk and $NotJunk flags. the problem
is that mail clients don't set these flags, or don't make it easy. thunderbird
can set the flags based on its own bayesian filter. it has a shortcut for
marking Junk and moving it to the junk folder (good), but the counterpart of
notjunk only marks a message as notjunk without showing in the UI that it was
marked as notjunk. there is also no "move and mark as notjunk" mechanism. e.g.
"archive" does not mark a message as notjunk. ios mail and mutt don't appear to
have any way to see or change the $Junk and $NotJunk flags.
what email clients do have is the ability to move messages to other
mailboxes/folders. so mox now has a mechanism that allows you to configure
mailboxes that automatically set $Junk or $NotJunk (or clear both) when a
message is moved/copied/delivered to that folder. e.g. a mailbox called junk or
spam or rejects marks its messags as junk. inbox, postmaster, dmarc, tlsrpt,
neutral* mark their messages as neither junk or notjunk. other folders mark
their messages as notjunk. e.g. list/*, archive. this functionality is
optional, but enabled with the quickstart and for new accounts.
also, mox now keeps track of the previous training of a message and will only
untrain/train if needed. before, there probably have been duplicate or missing
(un)trainings.
this also includes a new subcommand "retrain" to recreate the junkfilter for an
account. you should run it after updating to this version. and you should
probably also modify your account config to include the AutomaticJunkFlags.
- and don't have a global variable "d" in the big checkDomain function in http/admin.go.
- and set loglevel from command-line flag again after loading the config file, for all subcommands except "serve".
