we were already accepting, processing and displaying incoming tls reports. now
we start tracking TLS connection and security-policy-related errors for
outgoing message deliveries as well. we send reports once a day, to the
reporting addresses specified in TLSRPT records (rua) of a policy domain. these
reports are about MTA-STS policies and/or DANE policies, and about
STARTTLS-related failures.
sending reports is enabled by default, but can be disabled through setting
NoOutgoingTLSReports in mox.conf.
only at the end of the implementation process came the realization that the
TLSRPT policy domain for DANE (MX) hosts are separate from the TLSRPT policy
for the recipient domain, and that MTA-STS and DANE TLS/policy results are
typically delivered in separate reports. so MX hosts need their own TLSRPT
policies.
config for the per-host TLSRPT policy should be added to mox.conf for existing
installs, in field HostTLSRPT. it is automatically configured by quickstart for
new installs. with a HostTLSRPT config, the "dns records" and "dns check" admin
pages now suggest the per-host TLSRPT record. by creating that record, you're
requesting TLS reports about your MX host.
gathering all the TLS/policy results is somewhat tricky. the tentacles go
throughout the code. the positive result is that the TLS/policy-related code
had to be cleaned up a bit. for example, the smtpclient TLS modes now reflect
reality better, with independent settings about whether PKIX and/or DANE
verification has to be done, and/or whether verification errors have to be
ignored (e.g. for tls-required: no header). also, cached mtasts policies of
mode "none" are now cleaned up once the MTA-STS DNS record goes away.
we were trying to offset the timezone, but that makes no sense: we already
created a date in the local timezone based on (milli)seconds passed. so we can
just use that date instead of calculating a wrong date.
in smtpserver, we store dmarc evaluations (under the right conditions).
in dmarcdb, we periodically (hourly) send dmarc reports if there are
evaluations. for failed deliveries, we deliver the dsn quietly to a submailbox
of the postmaster mailbox.
this is on by default, but can be disabled in mox.conf.
with requiretls, the tls verification mode/rules for email deliveries can be
changed by the sender/submitter. in two ways:
1. "requiretls" smtp extension to always enforce verified tls (with mta-sts or
dnssec+dane), along the entire delivery path until delivery into the final
destination mailbox (so entire transport is verified-tls-protected).
2. "tls-required: no" message header, to ignore any tls and tls verification
errors even if the recipient domain has a policy that requires tls verification
(mta-sts and/or dnssec+dane), allowing delivery of non-sensitive messages in
case of misconfiguration/interoperability issues (at least useful for sending
tls reports).
we enable requiretls by default (only when tls is active), for smtp and
submission. it can be disabled through the config.
for each delivery attempt, we now store (per recipient domain, in the account
of the sender) whether the smtp server supports starttls and requiretls. this
support is shown (after having sent a first message) in the webmail when
sending a message (the previous 3 bars under the address input field are now 5
bars, the first for starttls support, the last for requiretls support). when
all recipient domains for a message are known to implement requiretls,
requiretls is automatically selected for sending (instead of "default" tls
behaviour). users can also select the "fallback to insecure" to add the
"tls-required: no" header.
new metrics are added for insight into requiretls errors and (some, not yet
all) cases where tls-required-no ignored a tls/verification error.
the admin can change the requiretls status for messages in the queue. so with
default delivery attempts, when verified tls is required by failing, an admin
could potentially change the field to "tls-required: no"-behaviour.
messages received (over smtp) with the requiretls option, get a comment added
to their Received header line, just before "id", after "with".
the bar is currently showing 3 properties:
1. mta-sts enforced;
2. mx lookup returned dnssec-signed response;
3. first delivery destination host has dane records
the colors are: red for not-implemented, green for implemented, gray for error,
nothing for unknown/irrelevant.
the plan is to implement "requiretls" soon and start caching per domain whether
delivery can be done with starttls and whether the domain supports requiretls.
and show that in two new parts of the bar.
thanks to damian poddebniak for pointing out that security indicators should
always be visible, not only for positive/negative result. otherwise users won't
notice their absence.
so full name/email address is visible.
using a hidden grid element that gets the same content as the input element.
from https://css-tricks.com/auto-growing-inputs-textareas/
a recent commit probably also make the compose window full-screen-width on
chrome, this restores to the intended behaviour of a less wide default size.
if you add multiple address fields, the compose window will still grow. not
great, in the future, we should make the compose window resizable by dragging.
the textarea is resizable (though it's not convenient to do in firefox which
only shows a dragcorner in the bottomright, usually located in the bottom
corner of the screen, so there is little space left to drag the corner; the
workaround is to move the window temporarily).
by using a String object as the textarea child. instead of a regular js string
that would be unicode-block-switch-highlighted, which would cause it to be
split into parts, with odd or even parts added as span elements, which the
textarea would then ignore.
according to the rfc's (2231, and 2047), non-ascii filenames in content-type
and content-disposition headers should be encoded like this:
Content-Type: text/plain; name*=utf-8''hi%E2%98%BA.txt
Content-Disposition: attachment; filename*=utf-8''hi%E2%98%BA.txt
and that is what the Go standard library mime.ParseMediaType and
mime.FormatMediaType parse and generate.
this is what thunderbird sends:
Content-Type: text/plain; charset=UTF-8; name="=?UTF-8?B?aGnimLoudHh0?="
Content-Disposition: attachment; filename*=UTF-8''%68%69%E2%98%BA%2E%74%78%74
(thunderbird will also correctly split long filenames over multiple parameters,
named "filename*0*", "filename*1*", etc.)
this is what gmail sends:
Content-Type: text/plain; charset="US-ASCII"; name="=?UTF-8?B?aGnimLoudHh0?="
Content-Disposition: attachment; filename="=?UTF-8?B?aGnimLoudHh0?="
i cannot find where the q/b-word encoded values in "name" and "filename" are
allowed. until that time, we try parsing them unless in pedantic mode.
we didn't generate correctly encoded filenames yet, this commit also fixes that.
for issue #82 by mattfbacon, thanks for reporting!
getting mox to compile required changing code in only a few places where
package "syscall" was used: for accessing file access times and for umask
handling. an open problem is how to start a process as an unprivileged user on
windows. that's why "mox serve" isn't implemented yet. and just finding a way
to implement it now may not be good enough in the near future: we may want to
starting using a more complete privilege separation approach, with a process
handling sensitive tasks (handling private keys, authentication), where we may
want to pass file descriptors between processes. how would that work on
windows?
anyway, getting mox to compile for windows doesn't mean it works properly on
windows. the largest issue: mox would normally open a file, rename or remove
it, and finally close it. this happens during message delivery. that doesn't
work on windows, the rename/remove would fail because the file is still open.
so this commit swaps many "remove" and "close" calls. renames are a longer
story: message delivery had two ways to deliver: with "consuming" the
(temporary) message file (which would rename it to its final destination), and
without consuming (by hardlinking the file, falling back to copying). the last
delivery to a recipient of a message (and the only one in the common case of a
single recipient) would consume the message, and the earlier recipients would
not. during delivery, the already open message file was used, to parse the
message. we still want to use that open message file, and the caller now stays
responsible for closing it, but we no longer try to rename (consume) the file.
we always hardlink (or copy) during delivery (this works on windows), and the
caller is responsible for closing and removing (in that order) the original
temporary file. this does cost one syscall more. but it makes the delivery code
(responsibilities) a bit simpler.
there is one more obvious issue: the file system path separator. mox already
used the "filepath" package to join paths in many places, but not everywhere.
and it still used strings with slashes for local file access. with this commit,
the code now uses filepath.FromSlash for path strings with slashes, uses
"filepath" in a few more places where it previously didn't. also switches from
"filepath" to regular "path" package when handling mailbox names in a few
places, because those always use forward slashes, regardless of local file
system conventions. windows can handle forward slashes when opening files, so
test code that passes path strings with forward slashes straight to go stdlib
file i/o functions are left unchanged to reduce code churn. the regular
non-test code, or test code that uses path strings in places other than
standard i/o functions, does have the paths converted for consistent paths
(otherwise we would end up with paths with mixed forward/backward slashes in
log messages).
windows cannot dup a listening socket. for "mox localserve", it isn't
important, and we can work around the issue. the current approach for "mox
serve" (forking a process and passing file descriptors of listening sockets on
"privileged" ports) won't work on windows. perhaps it isn't needed on windows,
and any user can listen on "privileged" ports? that would be welcome.
on windows, os.Open cannot open a directory, so we cannot call Sync on it after
message delivery. a cursory internet search indicates that directories cannot
be synced on windows. the story is probably much more nuanced than that, with
long deep technical details/discussions/disagreement/confusion, like on unix.
for "mox localserve" we can get away with making syncdir a no-op.
top-posting causes "On $datetime, $sender wrote:" above the quoted text to be
added (unless there was no Date header or valid address in a From header).
in the near future we should create settings, and add a setting for adding the
"on ... wrote"-line, ideally including a template.
for issue #83 by mattfbacon, thanks!
we set the flag both for move in imap and in webmail.
this also ensures the "MailboxDestinedID", used for per-mailbox reputation
analysis, is set in more reject-situations. before this change, some rejects
(such as based on DMARC reject) wouldn't result in reputation being used after
having been moved the message out of the rejects mailbox.
in the future, we need more tests for scenario's like this...
for issue #63 reported by x8x
may also help with issue #64
removing an item from the selected list should be done regardless of focus,
i.e. the code snippet shouldn't have been behind the "if (focus...)" condition.
we want to user to submit the stack trace. user can still edit before
submitting, but it won't look attractive to submit stacktraces with info that
shouldn't be there. not great that firefox is including too much info and the
effort we need to make to get it out again, but well.
increase() and rate() don't seem to assume a previous value of 0 when a vector
gets a first value for a label. you would think that an increase() on a
first-value mox_panic_total{"..."}=1 would return 1, and similar for rate(), but
that doesn't appear to be the behaviour. so we just explicitly initialize the
count to 0 for each possible label value. mox has more vector metrics, but
panics feels like the most important, and it's too much code to initialize them
all, for all combinations of label values. there is probably a better way that
fixes this for all cases...
we match messages to their parents based on the "references" and "in-reply-to"
headers (requiring the same base subject), and in absense of those headers we
also by only base subject (against messages received max 4 weeks ago).
we store a threadid with messages. all messages in a thread have the same
threadid. messages also have a "thread parent ids", which holds all id's of
parent messages up to the thread root. then there is "thread missing link",
which is set when a referenced immediate parent wasn't found (but possibly
earlier ancestors can still be found and will be in thread parent ids".
threads can be muted: newly delivered messages are automatically marked as
read/seen. threads can be marked as collapsed: if set, the webmail collapses
the thread to a single item in the basic threading view (default is to expand
threads). the muted and collapsed fields are copied from their parent on
message delivery.
the threading is implemented in the webmail. the non-threading mode still works
as before. the new default threading mode "unread" automatically expands only
the threads with at least one unread (not seen) meessage. the basic threading
mode "on" expands all threads except when explicitly collapsed (as saved in the
thread collapsed field). new shortcuts for navigation/interaction threads have
been added, e.g. go to previous/next thread root, toggle collapse/expand of
thread (or double click), toggle mute of thread. some previous shortcuts have
changed, see the help for details.
the message threading are added with an explicit account upgrade step,
automatically started when an account is opened. the upgrade is done in the
background because it will take too long for large mailboxes to block account
operations. the upgrade takes two steps: 1. updating all message records in the
database to add a normalized message-id and thread base subject (with "re:",
"fwd:" and several other schemes stripped). 2. going through all messages in
the database again, reading the "references" and "in-reply-to" headers from
disk, and matching against their parents. this second step is also done at the
end of each import of mbox/maildir mailboxes. new deliveries are matched
immediately against other existing messages, currently no attempt is made to
rematch previously delivered messages (which could be useful for related
messages being delivered out of order).
the threading is not yet exposed over imap.
they were not added to the list of attachments when sending the message to the
webmail frontend. they were shown on the "open message in new tab" page.
due to a missing return, the content was served again.
this path doesn't happen on release binaries, only during local development,
where there is a local file that can be served.
for example, when these mailboxes existed: "a", "a.b", "a/b", then "a.b" (.
before / in ascii) prevented "a/b" from being displayed in the tree below "a".
we only compress if applicable (content-type indicates likely compressible),
client supports it, response doesn't already have a content-encoding).
for internal handlers, we always enable compression. for reverse proxied and
static files, compression must be enabled per handler.
for internal & reverse proxy handlers, we do streaming compression at
"bestspeed" quality (probably level 1).
for static files, we have a cache based on mtime with fixed max size, where we
evict based on least recently used. we compress with the default level (more
cpu, better ratio).
